Yamaha Fx Cruiser Service Manual

27.01.2020
89 Comments

. 2008 WaveRunner FX SHO FX Cruiser SHO OWNER’S/OPERATOR’S MANUAL U.S.A. Edition LIT-18626-07-87 READ THIS MANUAL CAREFULLY BEFORE OPERATION!. Important manual information EJU30180 To the owner/operator NOTE: A NOTE provides key information to make Thank you for choosing a Yamaha watercraft. Procedures easier or clearer. This owner’s/operator’s manual contains in- formation you will need for proper operation, EJU30220 maintenance, and care.

A thorough under. Important labels.5 Yamaha Engine Management Warning labels.6 System (YEMS).40 Other labels.8 Yamaha Security System.40 No-wake mode. 42 Safety information.10 Cruise assist.44 Limitations on who may operate Multifunction information center. Reverse on waterways.83 Consumer information.110 Rough water operation.83 Limited warranty.110 Post-operation care. 84 YAMAHA EXTENDED SERVICE Transporting. 85 (Y.E.S.).112 Maintenance and care.

86 Flushing the cooling system. 86 Lubrication. Hull Identification Number (HIN), and engine serial number in the spaces provided for assistance when ordering spare parts from a Yamaha dealer. Also record and keep these ID numbers in a separate place in case your watercraft is stolen. General and important labels EJU30350 EJU30400 Emission control information Approval label of emission control certificate This engine conforms to 2008 U.S. Environ- This label is attached to the top of the cylinder mental Protection Agency (EPA) and/or Cali- head and to the inside of the engine compart- fornia Resources Board. General and important labels EJU30430 One Star - Low Emission Manufactured date label The one-star label identifies engines that This label is attached to the top of the cylinder meet the Air Resources Board’s Personal head.

Watercraft and Outboard marine engine 2001 exhaust emission standards. General and important labels exhaust emission standards or the Sterndrive and Inboard marine engine 2003-2008 ex- haust emission standards. Engines meeting these standards have 65% lower emissions than One Star-Low Emission engines. Four Stars - Super Ultra Low Emission The four-star label identifies engines that meet the Air Resources Board’s Sterndrive and Inboard marine engine 2009 exhaust emission standards.

General and important labels EJU30450 Important labels. General and important labels EJU35910 Warning labels.

General and important labels. General and important labels EJU35923 Other labels. General and important labels The following label indicates the correct direction to upright a capsized watercraft. The safe use and operation of this water- operate the watercraft craft is dependent upon the use of proper Yamaha recommends a minimum operator riding techniques, as well as upon the age of 16 years old. Common sense, good judgment, and ex- Adults must supervise use by minors. Safety information teristics of the watercraft before trying any EJU30760 Cruising limitations difficult maneuvers. Scan constantly for people, objects, and other watercraft.

Be alert for conditions that limit your visibility or block your vision of others. Operate defensively at safe speeds and keep a safe distance away from people, ob- jects, and other watercraft.

Safety information kles, and other bones. Do not jump wakes with another boat, which could result in se- or waves. Vere injury or death.

Do not operate the watercraft in rough wa- ter, bad weather, or when visibility is poor; this may lead to an accident causing injury or death. Safety information know that a helmet could help protect you in EJU30811 Operation requirements certain kinds of accidents and that it could All riders must wear a U.S. Coast Guard injure you in others. (USCG) approved personal flotation device A helmet is designed to provide some head (PFD) that is suitable for personal water- protection.

Safety information NEVER operate the watercraft after con- Always consult your doctor on whether it is suming alcohol or taking other drugs. Safe for you to ride this watercraft if you are pregnant or in poor health. Do not attempt to modify this watercraft!

Modifications to your watercraft may reduce safety and reliability, and render the water- craft unsafe or illegal for use. A mirror can also be used as an emergency signal.

Contact a Yamaha dealer or the U.S. Coast Guard for more information. Watch A watch is helpful so you will know how long you have been operating the watercraft. Always operate the watercraft in an This model is equipped with the Yamaha open area. Engine Management System (YEMS) that Do not touch the hot muffler or engine dur- includes an off-throttle steering (OTS) sys- ing or immediately after engine operation. Safety information Reverse can be used to slow down or stop any debris or weeds, which may have col- during slow-speed maneuvering, such as lected around the jet intake. When docking.

Once the engine is idling, shift into reverse and gradually increase en- gine speed. Safety information is required by law. Let the skier direct the EJU30940 Water-skiing operator’s control of speed and direction You can use the watercraft for water-skiing if with hand signals. It has the seating capacity to carry the opera- The spotter should sit astride the rear of the tor, a rearward-facing spotter, and the water- seat and hold onto the handgrip with both skier when he or she is not skiing. Safety information watch the skier’s hand signals and condi- until the watercraft is well away from the ski- tion. Er and slack in the ski rope is taken up. Make sure that the rope is not looped around anything.

After checking that the skier is ready and that there is no traffic or other obstacles, ap- ply enough throttle to raise the skier. EJU30960 Rules of the Road The vessel which does not have the right-of- Your Yamaha watercraft is legally consid- way has the duty to take positive and timely ered a powerboat. Operation of the water- action to stay out of the way of the stand-on craft must be in accordance with the rules vessel. Safety information give-way vessels).

Both you and the meeting provided the other vessel gives you the right- vessel must alter course to avoid each other. Of-way as it should. Meeting Overtaking If you are meeting another power-driven ves- If you are passing another vessel, you are the sel head on, and are close enough to run the give-way vessel. Safety information Fishing vessel right-of-way Many bodies of water used by boaters are en- All vessels fishing with nets, lines, or trawls tirely within the boundaries of a particular are considered to be “fishing vessels” under state. The Uniform State Waterway Marking the International Rules. Safety information They signify speed zones, restricted areas, danger areas, and general information.

Remember, markings may vary by geograph- ic location. Always consult local boating au- thorities before riding your watercraft in unfamiliar waters. Power Squadron. Watercraft Education and Training The Online Boating Safety Course, available through the watercraft section of the yamaha- motor.com website, is a free, 50 question learning course available to the public. Upon successful completion of 80 percent or better. Safety information EJU30990 Enjoy your watercraft responsibly You share the areas you enjoy when riding your watercraft with others and with nature.

So your enjoyment includes a responsibility to treat these other people, and the lands, wa- ters, and wildlife with respect and courtesy. Whenever and wherever you ride, think of yourself as the guest of those around you.

Features and functions EJU31010 Location of main components Front view 1 Handlebars 9 Bow eye 2 Rear seat 10 Hood 3 Front seat 11 Fuel tank filler cap 4 Footwell 5 Sponsons 6 Gunwale 7 Pull-up cleat (for FX Cruiser SHO) 8 Cooling water pilot outlet. Features and functions Rear view 1 Intake grate 2 Speed sensor 3 Stern eyes 4 Stern drain plugs 5 Reverse gate 6 Ride plate 7 Jet thrust nozzle 8 Reboarding step 9 Boarding platform 10 Electric bilge pilot outlet 11 Cleat 12 Handgrip.

Features and functions Control system 1 Remote control transmitter 17 Up switch (for cruise assist) 2 Watertight compartment 18 Down switch (for cruise assist) 3 Start switch 19 “SET” switch (for cruise assist) 4 Engine shut-off switch 20 “NO-WAKE MODE” switch 5 Clip 6 Engine stop switch 7 Engine shut-off cord (lanyard). Features and functions Engine compartment 1 Engine cover 2 Air filter case 3 Water separator 4 Fuel tank 5 Battery 6 Flushing hose connector 7 Electrical box 8 Engine oil filler cap 9 Spark plug cap 10 Dipstick. Features and functions EJU31021 To install the rear seat: Operation of controls and other Insert the projections on the front of the seat functions into the stays on the deck, and then push the EJU31040 rear of the seat down to lock it in place.

Seats To remove the rear seat: Pull the rear seat latch up, and then pull the. Features and functions To install the front seat: EJU36681 Hood (1) Insert the projections on the front of the To open the hood, pull the visor up, and then seat into the stays on the deck, and then lift up the hood. Push the rear of the seat down to lock it in place. If the remote control transmitter needs a System” on page 40 for information on using new battery or is not operating properly, the remote control transmitter.) contact a Yamaha dealer. Do not attempt to replace the battery yourself. ECJ00750 CAUTION.

Features and functions Refer to local hazardous waste regulations switch, such as if the operator falls off the wa- when disposing of transmitter batteries. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including in. NOTE: The engine will not start when the lock mode of the Yamaha Security System has been se- lected, the clip is removed from the engine shut-off switch, or the throttle lever is squeezed. (See page 41 for Yamaha Security System lock and unlock mode selection pro- cedures.).

This model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle steering (OTS) system. It will activate at planing speeds should you attempt to steer the watercraft after releasing the throttle lever. Features and functions Once the engine slows down, the watercraft otherwise the handlebars may suddenly will no longer turn in response to handlebar in- change position, which may lead to an put until you apply throttle again or you reach accident. Features and functions Use reverse for slow-speed maneuver- EJU31311 Quick Shift Trim System (QSTS) ing only. Selector Make sure that there are no obstacles or The QSTS selector is located at the left han- people behind you before shifting into dlebar grip and is used to adjust the trim angle reverse.

Features and functions There are 5 positions: 2 bow-down positions To enhance particular types of performance, (a) and (b), neutral “N”, and 2 bow-up posi- select bow down or bow up. Tions (c) and (d). EJU31330 Bow down To change the trim angle: Turn the QSTS selector to (a) or (b) and the (1) Reduce engine speed to less than 3000 bow will go down while the watercraft is on. Features and functions ahead acceleration when on plane and top EJU34861 Reboarding step speed are enhanced. The reboarding step provides a handhold and In some conditions, however, the watercraft footstep for boarding the watercraft.

May tend to “porpoise” (hop in the water). If the watercraft is porpoising, select neutral or bow down. (OTS) system.

EJU36760 Yamaha Security System The Yamaha Security System functions to help prevent unauthorized use or theft of the watercraft. The engine cannot be started if the security system is in the lock mode. The en- 1 Stern eye gine can only be started in the unlock mode. 1 Lock button 1 Remote control transmitter 2 Unlock button EJU36770 Yamaha Security System settings The Yamaha Security System settings are se- lected by pressing the lock or unlock button on the remote control transmitter briefly. 1 “UNLOCK” indicator light NOTE: The lock and unlock modes of this system can only be selected while the engine is stopped.

Selecting the operation mode 1 “L-MODE” indicator light There are two operation modes in the unlock mode of the Yamaha Security System: the NOTE: normal mode and the low-RPM mode. The If neither the start switch nor the remote con. Features and functions vated, the beeper sounds three times Digital Number No-wake mode oper- quickly and “5” (when miles are selected) speedome- of beeps ation ter display or “8” (when kilometers are selected) starts flashing in the digital speedometer Starts Activated flashing display. Features and functions switch. When the cruise assist is activat- NOTE: ed, the beeper sounds three times quick- The no-wake mode is also deactivated when ly and the digital speedometer display the engine is stopped. Starts flashing.

To keep the cruise assist EJU37021 activated, be sure to keep the throttle le- Cruise assist. Features and functions and the engine will respond normally to the beeper will sound one time quickly and the throttle. Engine speed will change. However, the ad- justment is limited to a maximum of five incre- ments above or below the initial cruise assist setting. Features and functions ponents for help and convenience in operat- EJU34930 Analog speedometer/tachometer and indi- ing the watercraft. Cator lights This watercraft is equipped with the following meter and indicator lights.

1 Analog speedometer/tachometer and indi- cator lights 2 Left multifunction display and operation but- 1 Analog speedometer/tachometer tons 2 “SPEED”. Features and functions “RPM” indicator light comes on when the an- EJU36800 “SPEED” indicator light alog tachometer is selected. The “SPEED” indicator light comes on when the analog speedometer is selected. 1 “Speed/RPM” button 2 “SPEED” indicator light 1 “SPEED” indicator light 3 “RPM”. The “UNLOCK” indicator light comes on when The left multifunction display is equipped with the unlock mode of the Yamaha Security Sys- the following functions. Tem is selected. The watercraft can be ridden normally when this light is on.

(See page 41 for more information.). Features and functions The following operation buttons are on the left Kilometers are selected as the display units side of the multifunction information center. At the Yamaha factory. 1 “Speed/RPM” button 1 “Volt/Hour” button 2 “Volt/Hour” button EJU37080 Digital speedometer The digital speedometer shows the watercraft speed against water. 18.1 volts, “HI” is displayed on the voltmeter.

If “HI” or “LO” is displayed, return to shore and, if necessary, have a 1 Fuel level meter Yamaha dealer check the charging system and the battery. NOTE: EJU36810.

(See page 63 for engine oil level checking procedures.) If the oil level is low, add enough engine oil to raise it to the proper level. If the oil level is sufficient, have a Yamaha dealer check the watercraft. NOTE: Press any button on the multifunction informa- tion center to stop the buzzer. If this occurs, reduce the engine speed, return to shore, and have a Yamaha dealer check the engine. NOTE: Press any button on the multifunction informa- tion center to stop the buzzer.

Features and functions The following operation buttons are on the ating, or if the display units are switched to right side of the multifunction information cen- miles/gallons/degrees Fahrenheit. 1 “Volt/Hour” button 1 “Mode/Reset” button 2 “SPEED” indicator light 2 “Start/Stop” button Compass To switch the display mode, push the This display shows the current direction of the. Features and functions Average speed Fuel consumption per hour This display shows the average speed in This display shows the current fuel consump- miles per hour “AV MPH” or kilometers per tion in gallons per hour “G/HR” or liters per hour “AV KMH”. Features and functions Water temperature surements are stopped.

The beeper sounds This display shows the ambient water temper- twice. Ature “L TEMP” (lake temperature). 1 “Mode/Reset” button 2 “Start/Stop” button Air temperature This display shows the ambient air tempera- NOTE: ture “E TEMP”. Features and functions EJU36831 To close the front storage compartment, push Front storage compartment down on the center of the hood until it latches The front storage compartment is located at securely. To open the front storage compartment, pull the visor up, and then lift up the hood. Features and functions To open the glove compartment, turn the To open the seat storage compartment, re- glove compartment knob, and then lift up the move the rear seat.

(See page 30 for rear seat lid. Removal and installation procedures.) 1 Glove compartment knob 1 Seat storage compartment 1 Glove compartment. Features and functions EJU35170 Beverage holder NOTE: The beverage holder is located on the star- Make sure that the watertight compartment board (right) side of the watercraft. Cap is closed securely before operating the watercraft. 1 Beverage holder NOTE: Do not place beverages in the beverage hold- er when operating the watercraft.

Gasohol containing methanol is not recom- dry rags. Always properly dispose of mended by Yamaha because it can cause gasoline-soaked rags. Fuel system damage and engine performance Avoid overfilling the fuel tank. Stop fill- problems. Operation EJU35613 ly 50 mm (2 in) from the top of the fuel Engine oil tank as indicated in the illustration.

Use a combination of the recommended SAE and API engine oil classifications. ECJ00280 CAUTION: Use only 4-stroke engine oil. EJU36860 Filling the fuel tank ECJ00290. Operation EJU31980 Pre-operation checks EJU31990 Pre-operation check list Before operating this watercraft, perform the checks in the following check list. See the accom- panying text in this chapter for details on how to perform the checks.

EWJ00410 WARNING If any item in the pre-operation check list is not working properly, have it inspected and repaired before operating the watercraft, otherwise an accident could occur. Operation NOTE: Pre-operation checks should be made each time the watercraft is used. These checks can be completed in a short time. It is worth the time spent to ensure safety and reliability. Check the hull and deck for cracks and other If the engine was running, allow the engine oil damage. If any damage is found, have a to settle by waiting 5 minutes or more before Yamaha dealer repair the watercraft. Checking the oil level.

EJU36870 Fuel level (2) Remove the seats. If the engine oil lev- el is significantly above the maximum lev- el mark, have a Yamaha dealer service the watercraft.

Operation the watercraft was capsized. Normally, the the water is discharged from the electric bilge water separator is empty. Pilot outlet at the stern.

1 Water separator 1 Electric bilge pilot outlet 2 Drain screw A small quantity of water will remain in the If water remains in the water separator, drain bilge and should be drained manually. Operation could be damaged, allowing water to en- place it if it is not in good condition. (See page ter the engine compartment. 99 for battery recharging procedures.) Make sure that the stern drain plugs are Also, check that the battery leads are tight- tightened securely before launching the ened securely and that there is no corrosion watercraft. Operation EJU32570 contact a Yamaha dealer or a fire extin- Fire extinguisher guisher dealer to obtain one meeting the Check that there is a full fire extinguisher on proper specifications.

Fire extinguisher: Classification: Capacity: 2 lb or more EJU32590 Throttle lever Check the throttle lever for proper operation. Operation turned, and that there is no free play between Also, make sure that the reverse gate goes up the handlebars and the jet thrust nozzle. Completely when the shift lever is pushed down. Check that the handlebars are locked in place. If the mechanism does not work properly, have a Yamaha dealer service it. EJU32650 Jet intake Carefully check the jet intake for weeds, de- bris, or anything else that might restrict the in- take of water. Operation come entangled in moving parts, result- EJU32670 Switches ing in severe injury or drowning.

ECJ00410 Stop the engine and remove the clip CAUTION: from the engine shut-off switch before Do not run the engine for more than 15 removing any debris or weeds, which seconds when checking the switches on may have collected around the jet in- land without supplying water, otherwise. WARNING Before operating your watercraft, become familiar with all of the controls. Consult a Yamaha dealer about any control or func- tion that you do not fully understand. Fail- ure to understand how the controls work could cause an accident or prevent you from avoiding an accident.

Operation (1) Launch the watercraft and start the en- (1) If the lock mode of the Yamaha Security gine. (See page 72 for engine starting System is selected, use the remote con- procedures.) trol transmitter to select the unlock mode. Operation (3) Attach the engine shut-off cord to your left (4) Push the start switch (green button), and wrist, and then attach the clip to the en- then release it as soon as the engine gine shut-off switch. Starts to run. 1 Clip NOTE: 2 Engine shut-off switch. 3 persons (or 2 persons if a water- children or others. (See page 41 for Yamaha skier is being pulled) to ride the watercraft at Security System lock and unlock mode selec- any time.

Operation Check state and local laws before operating fabrics, like those used in bicycle shorts. A full your watercraft. Wetsuit can also protect against hypothermia Operate defensively at safe speeds and keep (subnormal body temperature) and abra- a safe distance away from people, objects, sions. Operation vided, and keep their feet on the floor of the Practice reboarding in shallow water be- footwell. Never allow a passenger to ride in fore riding in deep water. Front of the operator.

EWJ00550 WARNING When passengers are on board, make sure that they are holding on firmly and have their feet on the floor of the footwell before you start to accelerate. Operation (2) Board the watercraft from the side or the EJU36350 Boarding alone rear. (1) Swim to the rear of the watercraft and (3) Attach the engine shut-off cord to your left place both hands on the boarding plat- wrist, and then attach the clip to the en- form, pull yourself up, and then grasp the gine shut-off switch. Operation start the engine, and then look in all direc- (1) Climb on board as noted in the previous tions before starting off. Section, and sit astride the seat. (2) Attach the engine shut-off cord to your left NOTE: wrist, and then attach the clip to the en- This watercraft is equipped with a reboarding gine shut-off switch. Operation tion, and then move to the seat and sit NOTE: astride to balance the watercraft.

When a passenger is boarding, both the pas- sengers and the operator should try to bal- ance the watercraft. (5) Check that the passengers have their feet on the floor of the footwell and are securely holding on to the person in front of them or to the handgrip provided. Operation (6) Gradually increase the speed to balance ride plate while pushing down on the gun- the watercraft. Wale with your right hand or foot. EJU33230 Capsized watercraft If the watercraft capsizes, turn it over immedi- ately.

Be sure to carefully follow the procedures be- low to prevent injury, or damage to the water- craft. Operation ECJ00550 B. Less throttle produces lower thrust, so CAUTION: the watercraft will turn more gradually. Do not operate the engine at full throttle for at least 1 minute after the engine has been restarted. Excessive water in the bilge can splash into the engine, which can result in severe damage.

Sharp high-speed turns may cause the watercraft to slide sideways or spin, throwing the operator and passengers overboard, which could cause an injury. This model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle steering (OTS) system. Operation steer away from a boat or other obstacle Once the engine is idling, shift into reverse that comes into your path. And gradually increase engine speed. Make Do not use the reverse function to slow sure that there are no obstacles or people be- down or stop the watercraft as it could hind you before shifting into reverse. (9) Wipe the hull, handlebars, and jet unit dry with a clean cloth. (10) Spray a rust inhibitor, such as Yamaha Silicone Protectant and Lubricant, on me- tallic parts to minimize corrosion.

(11) Allow the engine compartment to air dry completely before installing the seat. Operation EJU33461 Transporting When transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern eyes.

ECJ00641 CAUTION: Do not attach ropes or tie downs to any part of the watercraft other than the bow eye and stern eyes to secure the water- craft to the trailer. It is advisable 1 Flushing hose connector cap to have the watercraft serviced by a Yamaha 2 Garden hose adapter dealer prior to storage. However, the following 3 Flushing hose connector procedures can be performed by the owner. (2) Lubricate the areas of the watercraft Top off the fuel tank with fresh gasoline and specified in “Lubrication points” on page add one ounce of Yamaha Fuel Stabilizer and Conditioner per each gallon of fuel. EJU33661 Fuel system.

Specific gravity (for reference): 1.28 at 20 °C (68 °F) It is recommended to have a Yamaha dealer check the specific gravity and charge the bat- tery. If you maintain the battery yourself, be sure to read and follow the instructions provid- ed with the battery tester and charger you use. EJU33800 See a Yamaha dealer for genuine Yamaha re- Owner’s/operator’s manual and tool placement parts and optional accessories de- signed for your watercraft. It is advisable to always carry the owner’s/op- Remember, failures that are the result of the erator’s manual and tool kit with you whenev. Maintenance and care pairs.

The tools provided in the tool kit are suf- ficient for this purpose, except that a torque wrench may also be necessary to tighten nuts and bolts. 1 Tool bag 2 Screwdriver 3 16 mm box wrench 4 10/12 mm box wrench 5 Pliers 6 Open-end wrench. This “ ” mark indicates maintenance that you may do yourself. This “ ” mark indicates work to be done by a Yamaha dealer.

Initial Thereafter every Item. Maintenance and care Initial Thereafter every Item Operation hours hours hours hours hours Page months months months months Battery Check, charge Rubber coupling Check — Engine mount Check — Nuts and bolts Check — Air filter element Check Engine oil Replace 50 hours or 12 months Oil filter.

Fuel tank filler cap and seal for damage. Year or every 100 hours of operation. Fuel in fuel tank for water and dirt. Have a Yamaha dealer replace the oil fil- Fuel tank for damage, cracks, and leakage. Ter if necessary. EJU34310 Air filter element Have a Yamaha dealer check and clean or re- place the air filter element every 12 months or If the steering is stiff or misadjusted, have a every 100 hours of operation.

Maintenance and care If the reverse gate does not make contact with (3) Make sure that the handlebars are facing the stopper, have a Yamaha dealer service it. Straight ahead, and then adjust the free EJU37030 play by turning the adjuster. Do not at- tempt to diagnose any problems yourself. Have a Yamaha dealer service the watercraft. Remove and inspect the spark plugs periodi- cally; heat and deposits will cause the spark plugs to slowly break down and erode.

Maintenance and care To remove a spark plug: coil coupler could be damaged. The spark (1) Remove the seats.

Manual

(See page 30 for seat plug cap may be difficult to remove be- removal and installation procedures.) cause the rubber seal on the end of the (2) Remove the engine cover screws, and cap fits tightly. Lubrication points To keep moving parts sliding or rotating smoothly, coat them with water-resistant grease. Recommended water-resistant grease: Yamaha Marine Grease/Yamaha Grease A Throttle cable (handlebar end) Loosen the adjuster and disconnect the outer cable from the bracket.

Spray a rust inhibitor into the outer cable. Maintenance and care Shift cable (shift lever end) Grease quantity: Initial 10 hours or 1 month: 33.0–35.0 cm³ (1.12–1.18 US oz) (1.16–1.23 Imp.oz) Every 100 hours or 12 months: 6.0–8.0 cm³ (0.20–0.27 US oz) (0.21–0.28 Imp.oz) Shift cable (reverse gate end) 1 Grease nipple EJU34451 Checking the battery.

Battery life could be shortened. CAUTION: Be careful not to place the battery on its It is recommended to have a Yamaha dealer side. Charge the battery. If you charge the battery Be sure to remove the battery from the. EJU34490 Fuel injection system The fuel injection system was set at the Yamaha factory.

If the fuel injection system needs to be adjusted, have a Yamaha dealer service the watercraft. ECJ00220 CAUTION: Do not attempt to adjust the fuel injection system. Specifications EJU34542 Spark plug: Specifications LFR6A Watercraft capacity: Spark plug gap: 0.8–0.9 mm (0.031–0.035 in) Maximum people on board: Battery capacity: 3 person 12 V, 19.0 Ah Maximum load capacity: Charging system: 240 kg (530 lb) Flywheel magneto Dimensions: Drive unit: Length: Propulsion system: 3370 mm (132.7 in).

If you have any trouble with your watercraft, use this section to check for the possible cause. If you cannot find the cause, or if the procedure for replacement or repair is not described in this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service. Engine runs irregu- Fuel Empty Refill as soon as pos- larly or stalls sible Stale or contaminat- Have serviced by Yamaha dealer Fuel tank Water or dirt present Have serviced by Yamaha dealer Spark plug Fouled or defective Replace Incorrect heat range.

Yamaha 2006 Fx Ho Cruiser Service Manual Free

Watercraft slow or Shift lever Not completely shift- Push lever forward loses power ed into forward posi- until it stops tion Yamaha Se- Low-RPM mode se- Select normal mode curity System lected Cavitation Jet intake clogged Clean Impeller damaged. Trouble recovery EJU34620 contact with the rotating parts of the jet Emergency procedures pump. EJU34630 Cleaning the jet intake and impeller If weeds or debris get caught in the jet intake or impeller, cavitation can occur, causing jet thrust to decrease even though engine speed rises. (1) Connect the positive (+) jumper cable to If debris is difficult to remove, consult a the positive (+) battery terminals of both Yamaha dealer.

ECJ00670 (2) Connect one end of the negative (–) CAUTION: jumper cable to the negative (–) battery. Trouble recovery correct before attempting to start the en- (4) Replace the blown fuse with the spare gine. Any wrong connection could dam- fuse of the correct amperage by using the age the electrical system. Fuse puller on the reverse side of the cap. (4) Start the engine, and then disconnect the jumper cables by reversing the steps above. If the watercraft is submerged or flooded with bars. Water, follow the procedure below and consult a Yamaha dealer as soon as possible.

Failure ECJ00720 CAUTION: to do so could result in serious engine dam. Owner’s/Operator’s Manual. The owner of the watercraft shall give notice to an authorized Yamaha dealer of any and all apparent defects within ten 10 days of dis- covery and make the watercraft available at that time for inspection and repairs at the dealer’s place of business.

If you should move after you have purchased your new watercraft, please advise us of your new address by sending a postcard listing your Yamaha model name, engine number, dealer number or dealer’s name as it is shown on your warranty card, your name and new mailing address. This excellent Y.E.S. Plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.

Index Enjoy your watercraft responsibly. 25 Air filter element.94 Analog speedometer/tachometer. 46 Fire extinguisher.67 Analog speedometer/tachometer and Flushing the cooling system. 86 indicator lights.46 Front storage compartment.

56 Approval label of emission control Fuel and oil. Index Limitations on who may operate Rules of the Road.20 the watercraft.10 Limited warranty.110 Seat storage compartment. 57 “L-MODE” indicator light.48 Seats.30 Lubrication.87 Selecting the operation mode.42 Lubrication points.98 “SET”.

Index Yamaha Engine Management System (YEMS).40 YAMAHA EXTENDED SERVICE (Y.E.S.).112 Yamaha Security System.40 Yamaha Security System settings. YAMAHA MOTOR CORPORATION, USA Printed in USA January 2008–4.0 × 1 CR.

There's a lot that goes into owning a WaveRunner, but it should also be a rewarding experience. There's a lot you can do to make sure your time on a Yamaha WaveRunner is fun and that you're practicing safe habits. Before stepping on your WaveRunner, make sure you read the owner's manual for information on operation and safety.

Yamaha Fx Cruiser Svho Service Manual

Your WaveRunner requires periodic checks and lubrication to remain in efficient condition, so download a maintenance guide and keep track of all service intervals. Finally, make sure you have all required safety accessories and gear. You can find personal flotation devices, fenders, starter kits, and more at ShopYamaha.com.

Yamaha Fx Cruiser For Sale

2004 mini cooper owners manual uk. Plus, pick up some Yamalube® quality care and maintenance items, search for parts, and show off your Yamaha style with apparel and gifts!